Earth Notes: LED Lighting: Mini Reviews

Clas Ohlson 10W 1055lm dimmable "warm" white 18-1454 (5/5) B22

The ~20W CFL for our landing light died. I temporarily put in a 7W (~420lm) LED lamp replacement, but it clearly wasn't going to be bright enough.

So I bought the brightest B22 bayonet LED lamp that Clas Ohlson in Kingston had to offer, which is this interesting frosted beast consisting of eight separate yellowy-orange LED filaments. Presumably this construction allows for a illumination pattern closer to a tungsten GLS bulb rather than a more typical LED point source or three. This also claims a colour rendering index (Ra) of 90.

There was no non-dimmable lamp in Clas Ohlson at this output power (10W, 1055lm, ~75W incandescent equivalent). Normally I avoid dimmables because I assume that the extra electronics makes them more expensive and more fragile. Although we don't dim the hall light, this lamp has a pleasant soft-start feature and comes to full brightness over a short time (though under 1s to 60% according to the spec), which can be easier on the eyes in the dark!

The claimed efficacy of over 100lm/W is impressive. The LEDON managed a mere 60lm/W about seven years ago! The LEDON was a premium product; this unit, product 18-1454, was £7.99.

Clas Ohlson offers a two year guarantee, but suggests a 15,000h life which may be good for 15 years.

Maplin 7W 450lm "refrakta" "warm" (5/5) B22

Good 40W incandescent bulb equivalent in size and light volume (450lm), part number A51KN, but a little more expensive than competing brands when bought at ~£20, though ~£15 at 2012-06-18 which undercuts them.

On duty in our smallest room, the light volume (40W equiv) and colour is fine, and it is simple instant-on as you'd expect. (The packaging claims 60W equivalence, as do many 7W/~450lm lamps.)

Rated at 10,000h, and also comes in an ES27 screw/spotlight version (A50KN).

A reviewer (HG) found it to be fine (reviewing along with an Istoria candle):

We replaced low energy bulbs in a table lamp and an ceiling 'uplighter' shade. As both provide subdued lighting rather than light to read by we were perfectly happy with the brightness. Their light seemed a fraction whiter than our existing bulbs and we were fine with that too.

Clas Ohlson 7W 470lm "north light" "warm" (5/5) B22

For £17.99 in Clas Ohlson I picked up on 2011-01-02 a 7W "north light" with a bayonet (B22) fitting, labelled as 7W (40W equivalent) 470lm warm white (2700K), and with a 'standard' bulb shape (like the TESS/EQ60s previously reviewed), stock item 18-2314, for test.

The packaging claims a life of 15 years (15,000 hours) at 2.7 hours use per day.

This lamp is not dimmable.

Confusingly, part of the packaging states 100--240V 50Hz and elsewhere 220--240V; I assume that the latter is correct though it makes no difference for my purposes.

There are other fittings and styles and wattages now available at Clas Ohlson, such as an ES (screw) base version of this lamp, but also SES (small screw) golf-ball and candle style lamps up to 2W, so there is a decent range available. None of them were displayed powered up, and surely people are going to be reluctant to punt nearly £20 on a new technology without even being able to see what it looks like lit?

For my initial test I substituted this 7W lamp for a very-slow-to-start and insipid 9W CFL (CFLs of higher rating tend to be too big for the fitting) in our hallway which is only on for short intervals and for which instant-on is very handy, so the current CFL was not doing very well at all.

Firstly, being the size of a standard incandescent bulb, it fits!

Secondly, the instant-on behaviour is well worth having.

Thirdly, this lamp seems noticeably brighter than the 9W CFL even when the latter has had a while to warm up.

The light is even and warm and the lamp does the job.

It also meets with the approval of my partner!

On the strength of the performance of this lamp, we bought a screw (ES/ES27) version of this bulb (SKU 36-4241, 7W, 470lm, Ra 85, "warm white"/2700K, £17.99) to replace an expired 12W Philips "New Softone" CFL 2011-09-16 in the kitchen. And 2011-10-15 one to replace a 20W CFL in the bathroom, where its instant-on behaviour is valuable (it's rarely on for long); though as it's noticeably dimmer than the CFL after warm-up it was in time swapped out for the brighter LEDON 10W.

Note that reviewer LD, see below, found both this and another LED lamp reviewed at the same time, far too dim and didn't like the light colour, but on reflection this seems to be as much about expectations as the lamps!

(More photos.)

LEDON 10W 600lm "warm" white (5/5) B22

It had been hard as of end 2011 to get hold of anything more than about 7W (ie ~40W incandescent equivalent) for standard 240V domestic bayonet or ES fittings. I jumped at the chance to try the LEDON (Energy Saving Trust approved) 10W bayonet mains lamp though expensive at just under £30 including VAT. This has a 600lm output, and as advertised is 'very yellow' and to my eye more so than other 2700K-colour-rated 'warm white' lamps, and claims "exceptionally good colour rendering (90Ra)." A warmer and more orange tint to it than the slightly watery Clas Ohlson 7W.

The first place we've been testing it is in our small bathroom, which long ago was lit by a 60W or 100W incandescent as I recall, but we had a 7W LED (~470lm) bulb there for a while which we grew used to. My daughter and and partner both commented on the new lamp being noticeably brighter, which should make it easier to spot dirt on us and the surfaces! Reading in the bath was slightly hard work with the 7W lamp; the new one is a definite improvement there.

2018-03-14: smashed out of the ceiling and destroyed (along with the ceiling fitting) by my children today, while one was in the bath underneath. Ah well...

IstoriaLED 3.7W 200lm Candles "warm" (various fittings) (4/5) B22

2012-02-23 arrived from IstoriaLED four candle bulbs (3.7W, 200lm, 360 'effective' lm, 50000h, A+ energy rating, warm white, 240V/mains), identical other than for their different bases: ES14, ES27, B15, B22 (ie small and 'normal' Edison Screw, and small and normal bayonet).

Initial observations:

• Physically robust and pleasing design, with three double-sided lollypop emitters.
• Slight green tinge to light, and less warm than especially CFL bedside lamps.
• Similar light volume to 8W/7W CFL (E14) bedside lamps and 3W Clas Ohlson 3W golfball.
• Very clearly lower light volume (to be expected) than 7W cool white LED in anglepoise; too dim to work by.
• Base of ES27 too hot to touch after extended use; more so than other similar LEDs.

Several reviewers have now tried these out; one (LD) was disappointed by the light volume (possibly an expectations issue), though others (myself, HG, SB) have found it fine. Indeed, I am using the ES14 version in my bedside light where it replaces an 8W CFL (Philips) which in turn replaced a 40W incandescent and I feel that I am getting a good light level and colour cf the original!

HG said 2012-05-23: "... we were perfectly happy with the brightness. [The] light seemed a fraction whiter than our existing bulbs and we were fine with that too."

SB said 2012-09-10: "I think it's excellent. It is whiter than the other lamps in the same fitting but I prefer a whiter light. Unlike some people I like good bright, clear lighting and rarely choose the subtle more pink or yellow shades. It lights up faster than some of the other kinds of bulbs I have. So I'm quite happy with it."

ATL 909 Auto Dusk to Dawn Night Light (4/5) BS1363

Both our children's nightlights 2009 onwards were these 0.5W LED mains plugs, a tiny 1/10th the consumption of the incandescent type that we used before. Note that they don't actually seem to draw less power when they turn off in daytime, and we turn them off manually anyway.

We're very happy with these robust lamps.

Note: even the puny 0.5W these consume is horribly inefficient in that the vast majority is being turned into heat rather than light.

Maplin LED Strip Lighting plus Extension (3/5) BS1363

In 2011 I bought a basic Maplin 'decorative' LED strip lighting kit (A07JT) for the kitchen at the 'offer' price of ~£25, but only 'temporarily' fixed it up, actually sticky-taped (as very lightweight) under a cupboard above a work surface but we had not used it much as the quantity of light was maybe not quite what was hoped for.

(One attraction of this system was that the LED strips run at 12V, 12.1V measured at the unloaded mains adaptor in fact, so they could plausibly be driven from my off-grid 12V system if required. The strips are nominally ~0.53W each though the adaptor is rated max 1A ie 12W.)

The kit includes a mains adaptor, three LED (cool white) strips, various connectors and fixings, allowing the strips to be assembled many ways. Nicely done.

The extension kit of three more LED strips and more connectors and fixings (A08JT) that plugs into the existing strips and mains adaptor, came on offer again in Jan 2012 (~£15) so I bought one and fixed up the system properly to banish the worktop shadows between cooker and sink. The clips and screws are easy to use (the sticky pads were beyond me), and I'd put up the enlarged system in somewhere over half an hour.

As of 2012-07-01 we're not using this lighting very much.

2012-09-07 measured 'on' consumption as just over 8W and off as undetectably low (nominally <0.1W) so can be left plugged in for convenience without being a 'vampire'.

(More photos.)

Luceco 5.5W 470lm "G45 Classic Lamp" golfball 2700K "warm white" (5/5) ES14

Given how some of our old Philips CFL 8W golfballs are fading, these seemed worth a punt, and at £2 each and reasonable efficacy, seem good value for money.

I quietly replaced a couple of the CFLs in the livingroom, and the 2W bulb in my son's bedroom which I am now finding hard to read by, to see if anyone notices! In the former, the instant-on of the LEDs is clear to me, and the remaining CFL looks a little sad; in my son's room the new lamp is clearly brighter and I'll just have to see if reading is easier on my ageing eyes...

Clas Ohlson 2W 135lm "north light" golfball "warm" (5/5) ES14

In December 2011 we bought a Clas Ohlson golfball 2W 250lm warm-white (2700K) 15000h LED bulb with a bayonet (B22) fitting (18-2313) for the in-laws to use in place of an existing 15W incandescent night-light which is all ~8h/night every night. They seem to like it (and report it as brighter than the 15W). Should save them ~£4/y at 2012 prices, or a 2-year payoff.

Clas Ohlson 3W 250lm "north light" golfball "warm" (5/5) ES14

In December 2011 we bought a Clas Ohlson golfball 3W 250lm warm-white (2700K) 15000h LED bulb, with a small screw (SES/ES14) fitting (36-4641) as a signficiantly brighter replacement for the Philips "AccentWhite" 2W in my boy's room

This seems comparable to or brighter than the 7W/8W CFL golfballs we have in our house, eg in bedside lights...

Clas Ohlson 4W 160lm PAR16 SES Spot 3000K (4/5) ES14

I bought a 4W SES spot (36-4237) for a friend to try at his train-station coffee stall, where it replaces a 40W incandescent. It seems a very similar level of available (cool) light, on 10% the power! At ~8h/day use I think it may be saving him about £1/month as of mid 2011, and though not all 10 of the positions are ripe for LED replacements (eg due to the steam belching from his fancy Italian coffee machine, where instead we have tried halogen bulbs at a 30% or ~30p/month saving) several of them are. They'd pay for themselves in electricity alone in 18 months, and maybe again in replacement incandescent bulbs in its 20-times-longer life (ie 20000h vs 1000h for the incandescent), never mind avoiding the fiddle and annoyance of replacing the bulbs.

(As to reliability: all the other non-CFL non-halogen low-energy bulbs we tried, ie CFLs, were too fragile one way or another and failed fairly quickly in the moderately harsh environment ie significant cold/heat, steam, etc.)

We replaced a second incandescent with one of these LED lamps ~July 2012, and he's happy with it.

Philips 2W AccentWhite "warm" candle (3/5) ES14

As of the end of January 2010 the 20W halogen lamp that we were reading to younger child by physically broke and was unsafe, so we spent £4 on a small simple bedside E14/ES14 (14mm Edison Screw) bedside lamp, and although it's not on much and we had spare ES14 incandescents I thought I'd see what LED lamps were available retail in our local shops. At least two shops had 2W candle-style lights available for ~£10, so I bought the Philips "AccentWhite" warm white from John Lewis. (Actual consumption seems to be 1.6W, with a power factor of ~0.4.) Nothing of a higher rating was (yet) available in that fitting in LED, though 7W/8W CFLs such as the one in my own bedside light are. Nominally it has 20 years' life (20,000h) though I suspect that it might outlast me!

Note that this lamp takes a second or so to come on (though is then at full brightness, so is not 'warming up' like some CFLs), which can occasionally be slightly disconcerting.

(More photos.)

Light Planet (TESS) 7W 450lm EQ60 Spotlights "warm" and "cool" (5/5) ES27

Extensive testing/use of a pre-production and production "warm" and "cool" Light Planet (TESS) EQ60 lamps (in kitchen spotlight and office anglepoise) over two years (2010 to 2012 so far) have been very satisfactory; pleasant solid light, though consumption measured at >7.5W. The bulb is light enough for my anglepoise whereas many CFLs have not been.

As of 2012 the "cool" lamp is in daily use at my desk and is good to work by because of its light volume and colour, and the "warm" in the kitchen for its warm tone where it meets with approval.

A colleague, doing an energy-sensitive refit of his house, found the EQ60 'warm white' too yellow and too narrow a beam for his purposes, (but found the "V3" GU10 spot's output beam remarkably wide and even). Another tester, who had complained about her 'too yellow' CFLs causing headaches found the 'cool' EQ60 too harsh and clinical.

I think that a more 'neutral' (say 4000K) tone would be a useful addition to the range for both the EQs and the V3s (see below), though Light Planet feels there would be some obstacles:

Trying to produce a third product in the range would be difficult, due to the commercial commitments on the current chip sets. May be able to introduce them at a later date.

(More photos.)

Civilight 5W Spotlight "Cool" (6000K) White (2/5) ES27

We eventually found a good site in our kitchen for the 5W LED "cool" (6000K) spot from UltraLeds.co.uk (which was the highest power available ~2007), marked on the side "civilight", and though it is a little weak/watery, it works fine with the blue elements of the decor. (One issue with a light that is going to last many many years and cost lots is that we'll have to think about and plan more carefully what we buy, whereas before we knew we'd be buying a new bulb inside a year anyway, and didn't have much choice in light colour nor CRI/rendering issues.)

Note: this bulb caused significant interference on a VHF FM radio about 2m away, unlike the CFLs in the same spotlight lighting strip.

This item failed after a little over 2 years with Ultraleds offering no help even though one might find this early failure "not fit for purpose".

Update 2010-03-19: One of the first highish-powered domestic LED bulbs (5W Edison screw) that we have been testing failed after a little over 2 years' use. Ultraleds (and their MD) with who I had previously been impressed were dismissive about my suggestion that devices sold in part on a promise of long life should be considered "not fit for purpose" if they fail this quickly, regardless of nominal warranty period.

Update 2012-02-01: I finally disassembled the unit to extract the board with 5 series LEDs, which draws 60mA@14V (0.8W), 200mA@15V (3W), 340mA@16V (5W+), ie about 3.2V/340mA for rated output, if heatsinked on the original case. So I could use it as part of my LiFePO4 battery dump load with care.

InLight 4W 350lm INL-22549 3000K 60° A+ (5/5) GU10

In our kitchen I have replaced 7W lamps with these with little apparent loss of illumination, bringing each of the two strings down to 20W as of 2016/08, for maybe 18kWh/y saved (3 lamps x 3W savings per lamp x 2000h/y on-time). That would be ~1% of our gross electricity consumption, largely when local microgeneration from solar PV is not available to supply it, thus reducing imports from the grid more as a proportion.

2022-07-01: one lamp failed flickering fast and annoyingly. Seemed hot.

Superflare 6W 540lm GU10 non-dimmable 60-degree-beam 2700K "warm" (5/5) GU10

James P of Furzefield International Limited offered me one of these Superflare GU10 6W 2700K lamps to review out of the blue, and as I'd just leant one of my favourite warm white GU10s to a neighbour having second thoughts about her new LED lighting, I was pleased to give this lamp a test. I like it; in a perfect world I'd aim to match or beat the 100lm/W I have elsewhere and have a slightly less warm/orangey shade at (say) 3000K+, and have a slightly cooler case when running too, but this does a good job as-is.

In particular at the end of 2012 I have being trying to use warmer lighting in the evening in case it helps with sleep later, (and indeed running f.lux on Mac and Windows to adjust the display colour too), so the arrival of the Superflare was timely.

The Superflare's light colour and volume was liked in our kitchen, eg as compared against the Aurora V3 and recent Clas Ohlson and unbranded SMD 5050, being brighter than all the rest and nominally pretty efficient.

I also appreciate at my desk the light volume which is similar to the 9W dome lamp though a nicer shade and distribution (the Superflare claims a CRI of over 80 and relatively-wide beam angle), as well as again nominally much better on efficiency (A-rated, 90lm/W).

(I use a GU10 in a goose-neck sometimes as desk task lighting or more often as a uplighter for over my desk.)

The lamp's 'Chip on Board' (COB) technology gives a wide solid appearance to the emitter, rather than a very narrow point or a number of such as is more common.

2013-01-01: the lamps are available through Amazon at ~£12 one-off, or ~£10 for a discounted set of nine. (Also trailed were some dimmable lamps at a slightly reduced 500lm output.)

2013-06-12: took delivery of three more Superflare for use between the kitchen and my desk; bright pleasant warm colour and relatively low glare.

2016-08-07: consistently pleasant to use and reliable over several years, have increased rating to 5/5.

2021-03-26: a Superflare lamp failed a bit before 8am. There is what looks as if it might be a burn spot on the COB. The lamp died with a flash.

Clas Ohlson V-Light 6W 380lm GU10 dimmable 36-degree-beam 3000K "warm" (5/5) GU10

I broke my anglepoise that I'd been using with my 7W "cool" LED, finding the light volume from my 3W Livarno not always enough, and being slightly concerned about lots of research and media reports about bluer colours disrupting sleep when used (for work) in the evening, I decided to try an upgrade to the new 6W/380lm GUI (36-5094) lamp from Clas Ohlson 2012-09-05.

(I am especially happy to buy from Clas Ohlson as one of only two retailers in my town that is currently happy to take back WEEE (failed/expired electronics) and which may save me a long walk to the 'official'/legal disposal point here.)

The light volume and colour is good. I am finding it most comfortable to use the light indirectly, bounced off ceiling and wall, as sideways leakage from my unshielded gooseneck desktop is otherwise a little distracting.

I don't have any way to test the dimming, and would have preferred a version without to save a bit of money and presumably improve overall efficiency though >60lm/W is fine as-is.

The white apparently-ceramic body gets quite hot, though not burning hot, which presumably indicates good conduction of heat away from the LEDs which may help prolong the lamp's life.

The pack is interesting in indicating a lifetime in power cycles (15000) as well as on-time (25000h) when generally LED lamps are not thought of as cycle-limited.

Failed (went very dim) 2016-05-30: Clas Ohlson exchanged in store for equivalent without fuss (old 36-5094, new 36-3600 345lm/6.5W). I suspect that the new spec is equivalent to the old, with the prevalent naughty 10% "fudge factor" taken out on both sides.

Device dated 2018-05-30 failed 2021-03-29. It may have been unused for a while, though having shuffled lamps around after a failure a few days ago I'm not sure. Also went very dim. Minded to drop rating from 5 to 3 given short working life.

Light Planet (Aurora ALTLED) V5 7W 720lm "cool" Spotlight (5/5) GU10

Light Planet on 2010-09-16 kindly supplied me with a "V5" 7W, 720lm, 38° beam angle, 5000K--6350K "cool", GU10 LED sample for evaluation, still in use every day as of 2012-07-08!

Interestingly it is rated 100V--240V AC, so suitable for markets worldwide.

The stated efficiency (~100lm/W) puts it well ahead of most CFLs. For example, a new 7W Philips "golf-ball" "warm" SES CFL is labelled as 310lm (and the equivalent of 31W incandescent), 10000h, 50000 on/off cycles, and 1.4mg mercury to boot. On the supplied scale, 720lm comes in at just under 60W incandescent.

This lamp is bright (only a 40W or 50W GU10 halogen or good 12W CFL should be able to match or beat its light output in that fitting), and it is fast to come on.

One generic point about these intense point sources rather than (say) CFLs, is that they seem much more headache-inducing when caught in peripheral vision, so their arrangement is more critical than just what they light; more smaller lamps, or more chips within each lamp, may help. This particular device has 4 emitters, whereas the Livarno light with 25% the lumens output has 15!

I have now bought the 12V (MR16) version of the V5, also cool white, and it is every bit as bright as the mains (GU10) counterpart, and a stained-glass artist to whom I lent it has been very happy with its colour rendering at her work desk even though initially taken aback by its coolness compared to the halogens she was used to.

(More photos.)

Update 2010-09-16: Aurora "V5" 7W 720lm "cool" GU10 evaluation unit arrived from Light Planet (thank you!). Has a 4-chip array internally. Should match/beat 40W of halogen GU10 or about 12W of a good CFL in light output, and is more efficient than CFL.

Light Planet (Aurora ALTLED) "V3 Ultimate" 7W 355lm Spotlight (4/5) GU10

We have been testing a couple of the (warm) "V3 Ultimate GU10 LED Spot Lights" in a specially-installed 'test' lighting fixture in our kitchen (2010--). We're getting less lumens per Watt in this GU10 style than with the EQ60, but that's in part because the GU10 fitting is hostile to non-incandescent technology in general being designed to retain heat which is good for halogens but bad for LEDs/CFL. CFLs in this format seem to be limited to ~50lm/W also.

(In 2012 I would expect new GU10 lamps to beat 60lm/W, but these were relatively early models and are still much much more efficient than halogens.)

I asked a colleague and their spouse to try Light Planet's 7W warm-white spot (GU10/240V, 355lm, 2850K--3000K, CRI 70, 120° beam angle), their spouse being a medic who likes everything "like an operating theatre" and thus wants a decent volume and 'quality' of light, and they were sufficiently impressed to replace all the halogens in that room with these devices! Indeed, they report the halogen bulbs as looking weak and watery by comparison. (Note that a typical 50W halogen apparently emits up to 900 lumen, 35W/~600lm, though I see 12lm/W typical quoted, and light temperature of ~3000K is common.)

The V3 light quality is pleasant, and unlike the CFL GU10 that the comparison is against, is almost instant-on (within a second). The 'warm' tone suits our yellow walls.

The beam angle is 120° and thus barely a 'spot' in fact, which also suits our purposes fine.

When alongside an Omicron 11W GU10 CFL (2700K), the LED is faster to come on (almost instant, with no "warm-up" phase) and of very similar colour after a few minutes when the CFL has stabilised. Both are fairly pleasing to the eye in terms of design and appearance, though the CFL has a longer body that protrudes from the fitting, so the LED wins on that element.

We'll have continued ro like the light tone in the darker months of winter with less bright natural (cooler) light around. I can also report that it is pleasant to use at night, warm and full, unlike the watery 5W 'cool' LED lamps we tried in a similar position.

We like the V3, and would only hope for a greater efficiency (lm/W) and greater power output (ie more light) in future revisions.

Update 2010-01-15: Swapped in the 7W/355lm "warm white" (2850K--3000K), CRI 70, 120° beam angle Aeon (Taiwan) ALTLED Aurora V3 M02GW007KC-90, -20°C--40°C ambient, 100V-240V AC, 50/60Hz GU10 spot/downlighter for my daughter's current bedside 3W 6000K LED, and it is as expected much brighter and warmer. It also looks a little more delicate (more fins at the front) and interestingly takes something like a second to switch on, and quite a few seconds to completely fade to off. (A quick test of the ES bulb in my desk reading lamp replacing a new 12W "softone" CFL seems satisfactory too, this evening.)

(More photos.)

Unbranded 3W 340lm mains 24-chip SMD 5050 "warm" white (4/5) GU10

From Alarms and Lightbulbs (note bulk pricing; I bought 1-off at ~£9 Jan 2012) this 3W 340lm 24-SMD chip GU10 lamp is nice and bright (not far off the 7W ~355lm Aurora V3s by eye) and does provide a slightly more spread and less-point-source beam, with a decent colour.

120° beam angle, claims to be brighter than a 50W halogen, 220--240V.

I'd be slightly concerned about the SMDs getting covered with grot or even presenting a slight extra shock risk or moisture ingress route, but that may be overthinking the plumbing. The lack of branding would concern me in terms of expected life, but the lamp is pretty good for the price if that is no issue.

Multicolour 1.5W Auto-changing LED (4/5) GU10

Just for a bit of 2011 winter silliness I swapped out one of the GU10 (240V) lights in the kitchen (a 11W CFL) for a Maplin N27HA "1.5W Auto Changing Multi Colour LED GU10". Not especially bright but the colours are indeed "vibrant" as claimed; the kids like it.

Philips Econic 3W Spotlight (4/5) GU10

The first thing to be careful is that there are apparently as at 2010-08-10 two versions of this in circulation, one marked 15 year life and the other 25, and neither marked on the packaging with lumens output, and Philips' own site is coy too, and their customer enquiries initially suggested 300lm output which would be remarkable, and then a week later called me back to say 220lm. This confusion is unhelpful at the very least, and I expect better of Philips.

I have borrowed one of the devices labelled as 25-year life (25,000 hours), which I take to be the same as this Argos 432/9244 lamp, which is given as 250lm, ie ~80lm/W, thus beating the V3 in efficiency if so. By eye the light output is not remarkably different from the 7W V3, even allowing for the slightly different light colour and very different beam (a spot at the 25° claimed on the packaging that I have), though a subsequent rough comparison with other lamps suggests that it is maybe less than 200lm, 150lm if Philip correctly identified it (see below).

This bulb is slightly shorter than the V3, at 50mm, and does not protrude at all from our kitchen fitting.

The lamp is 'instant-on'.

My daughter preferred this 3000K/warm light over the current 6000K/cool lamp in her bedside light.

My partner liked the light quality in our kitchen.

A friend Philip C, see below) described it as not looking "quite so much like a gadget from an episode of 'Blake's Seven'" compared to the V3!

This lamp seems to be matching or beating standard CFL efficiency, which is hard to do to this style of fitting. At £20 it's still quite expensive, but the Argos page claims that it will last as long as 25 (35W) halogen bulbs at about £2.50 each, so likely cost-effective even ignoring the substantial energy savings.

The adult-proof plastic display packaging is pretty but excessive, so another small black mark against this product.

(More photos.)

Lidl Offer Livarno 3W 3000K 180lm Spotlight "Edi Light" (4/5) GU10

On 2010-09-02 Lidl had an offer of £5.99 for 3W LED lamps, in various fittings including GU10, Livarno brand (EDI Light GmbH), and claiming ~60lm/W on the box, ie about 180lm total. This lamp seemed less bright than the Econic with a by-eye comparison, but the beam angle of 90° of this lamp cf the Econic 25° confounds such testing.

This does well in efficiency terms compared to CFL (at least as good) especially given the GU10 fitting.

The light is a pleasant colour, and the multiple (15) emitters/chips (possibly SMD 5050 style) make for a less harsh 'point-source' feel.

My daughter preferred this to her previous (6000K LED) bedside lamp, primarily because this illuminates the far end of her bed better given its broader beam; it seems to throw significant useful light beyond the 90° stated, possibly in part because of its slightly domed front.

This comes on quickly, faster than the V3 for example.

Like the Econic, this claims a 25,000 hour life.

(More photos.)

Unbranded 3W mains "cool" white (4/5) GU10

Our young daughter's bedside light was an unbranded 3W 240V mains GU10 "cool" (6000K) LED in a gooseneck lamp from 2008 up to late 2010 directed up at the ceiling as indirect lighting, replaced Sept 2010 with a Livarno 3W warm white GU10 also reviewed then later with a CFL 'kitten' lamp birthday gift, and worked well for her.

It's officially my office soldering/closework desk/work spotlight, but I don't need it most of the time and it did well in this alternate role! When I was young my bedside light was a 60W incandescent; this is safer and cooler and probably represented a distinct energy saving.

My daughter is also tester for other GU10/240V lamps that cross my path!

(More photos.)

Home-brew rechargeable night-light (5/5)

We decided that it might help our daughter find her way to the loo in the night, and help us to get around at night without turning on the main overhead light on our upstairs landing possibly disturbing both children, to try a night light there.

The upstairs corridor does not have a single power socket, so my first attempt was to try using a 3W (cool white) MR16 12V lamp from my solar off-grid system, temporarily hooked up at the master bedroom door. It's certainly enough to see by, even downstairs, but was too bright and kept us awake at night. Also the power drain is a bit more than I'd like from my off-grid system (the 'official' server drain is under 4W!).

Now we have a homebrew solution based on rechargeable NiMH batteries that lasts several months between recharges, or more if the built-in solar cell is used to keep it all topped up. See the whole story!

Maplin N34HN 50 white LED solar fairy lights (4/5)

As of November 2012 we've had these two or three years with the only problem being a sticky switch between modes on the back, which is unusually good for this type of product.

50 cool white LEDs on 9m of cable, solar powered, can flash or stay steady (how we usually have them), but no fancy effects such as running lights.

Wilkinson Own-Brand 97p Solar Garden Lights (3/5)

In June 2010 we thought we'd look at a simple cheap solar-powered garden light to see if they are any use. They don't give out a huge amount of light and there is an embedded environmental and energy cost even if they don't need mains or batteries. We splashed out on two of these.

These are very simple and cheap and physically small and light, possibly using a supercapacitor inside rather than a battery, powering a single cool-white LED pointing out the base of the unit through a clear plastic prismatic diffuser. The light given out is fairly weak but pleasant accent lighting; it wouldn't much help, for example, with navigating the garden at night.

Each unit consists of a small 'amorphous' brownish solar cell on top, a black plastic body with a thin metal covering sheet, and a removable diffuser and spike for planting in the earth. Under the diffuser/spike is a switch to turn the light off, thus presumably saving its juice for another day or if packed away.

My 19-month old boy managed to disassemble and break one unit fairly easily requiring the LED's leads to be resoldered to the board, but all-in-all the unit seems robust for normal uses!

These could be nicely adapted to make solar-powered lights for a doll's house, or for children's night-lights with some extension of the LED leads (one seems to last about 4 hours when fully charged).

All were dead after a year.

(More photos.)

Robert Dyas 148578 Bonnington solar garden light (1/5)

This product appears to be identical to the Wilkinson's 97p solar light previously reviewed, and though individually much more expensive at 2012-06-24 at £1.49 a shot, at 5 for £5 inflation has been kind...

Less kind is the fact that all the Wilko lights failed within a year, thus creating an e-waste (and emboddied energy) problem; let's hope these are better.

These have the oddity that the little solar panels on top have a variable number of stripes (about 2--5) which indicates a very variable voltage for the electronics to deal with (albeit the gathered solar power will be the same).

Update 2013-01-01: all long-since dead: very poor.

RS PRO GU5.3 LED Reflector Bulb 5 W(35W) 2700K, Warm White (5/5) MR16

See RS catalogue page for Stock No 123-7961.

Initial comparison with the Istorial 4.5W MR16s is that this is a little brighter than the 'warm' lamp and maybe a little less bright than the 'cool' lamp. This is nominally slightly lower lm out and higher W in than the Istoria warm, though historically many manufacturers rounded lm up and W down to allowed legal tolerances, so it is not possible to be sure!

The RS lamp is much warmer, and the Istoria more watery.

This lamp is getting hotter to the touch than the Istorias, which is reasonable given their huge metal heatsinks.

Nominal specs: MR16, GU5.3, 12V, 5W, 2700K warm white, 345lm, A+ efficiency.

Purchase price 2019/03 was ~£3.38 (inc VAT) per lamp, when buying three.

IstoriaLED 4.5W 351lm 12V Warm and Cool (5/5) MR16

At the Energy Solutions Expo October 2011, IstoriaLED very generously gave me a couple of review samples (one warm/2700K+, one cool/6000K+). Both have an A+ energy rating, are 4.5W and 351lm (650 eff lm) and 50000h life. Initial subjective testing suggests that the cool light is nearly as bright as my 720lm/7W Aurora V5.

The cool seems much brighter than the warm (I expect some difference, but not this much).

I'm a big fan of these and work by the "cool" lamp at my desk instead of the 7W mains EQ60 as of 2012 sometimes to be completely 'off-grid' for lighting.

I've lent both the "warm" and "cool" lamps to a friend (MF) considering replacing 12V MR16 halogens in his bathroom for energy efficiency reasons, and once he'd overcome some transformer trouble (not liking the very low load that these lamps present cf halogens) declared that he would be happy with either colour and that the light volume was good for his purposes.

Maplin "refrackta" 3W 110lm 12V "warm" (3/5) MR16

Maplin part N19HT, claims 50000h life, 30° beam angle, 3150K light colour, 12 DC/AC. Light colour is fine, ergonomics OK also.

Bought this in a hurry for a school educational exhibit (early 2012) without noticing the poor luminous efficacy (~37lm/W) at about half that of good lamps in this style and maybe only three times that of halogens.

LED torch bulb replacement (5/5) P13.5S

Fine direct efficient replacement for existing incandescent lamp/bulb in existing torch. Worked well will NiMH rechargeables with very long life per charge and little appreciable dimming. Cool white light. Outlived the two (cheap) torches that I used it in!

I think that the fitting was P13.5S (Single Contact Miniature Flanged Base).

Update 2010-01-11: Thurmond in Texas very kindly sent me an assortment of power LEDs to play with! The very first thing I did was replace the incandescent bulb in my daughter's 2-cell (NiMH rechargeables) torch with one of the pieces Thurmond provided, and it gives a much brighter (and bluer) light and should proably last longer. Even better, those cells were charged in the summer from our PV. The LED bulb itself survived two cheap torches being smashed containing it, by my children's "youthful exuberance"...

9W 500lm 12V warm-white (3500K) LED dome lamp (4/5) wired

Decent 12V warm light bought 2008-08-22 that as of 2012 I still use as an alternative to my "cool" mains or 12V desk lighting from time to time. Good light volume (~40W incandescent equivalent) in interesting 'bulkhead' design.

Update 2008-08-23: Yesterday I ordered from UltraLEDs one of these warm-white (3500K) 9W 500lm LED dome lamps and added to my RE system. It arrived today: very good service! The dome's light intensity and colour is very close to that of a similar wattage 'warm' (mains) CFL that I have in the same room, and should be a little less depressing to work by on a cold winter's evening than the cool-white... Having both the dome and the spot on at once is pleasing too. The 9W dome light cost £40 (~USD80) whereas a similar-rating CFL might cost 1/10th of that, so the technology is here but the price needs a little work for prime-time...

3W car modding light "cool" white (4/5) wired

Bought 2007-06-04 and used until only 2007-09-23 as too dim to work by, but it was the first decent-output LED I had. Still in use in 2014 as a test and a part of the dump load on my LiFePO4 battery system. Has flying leads for connection. "Cool" white colour. Robust build for exterior car use for 'modding' visual effects, which I take also to mean electrically robust.

Update 2007-09-23: I stopped using the 3W LED 'car modding' light as backlighting some time ago, various others used since then including 6W warm-white LED ~2014.